Express Painting - Mobile Banner
express painting
expresspainting tab know more

Waterproofing Solutions

Waterproofing Solutions

Damp/ Wet Patches Leakage in Bathroom/ Kitchen/ RCC Tanks Leaking Roofs and Parapets Cracked Plasters Weak Plasters/ Masonry Walls Building Repairs Stained Tiles Weak Tile Adhesion/ Leakage in Tile Joints
Our Waterproofing Solutions are designed to provide added layers of protection to keep your home safe from waterproofing issues.
Waterproofing Solutions

Damp/ Wet Patches +

Damp/ Wet Patches

Dampshield 2K

Method of Application
Surface to be treated must be thoroughly cleaned from all kind of laitance, oils, grease etc.

A. For minor damped areas

  • Mix Dampshield 2K Base: Catalyst: Water in the ratio of 1:1:1
  • Apply one brush coat over the affected area over the plaster
  • While 1st coat is dry, apply 2nd coat (generally give 4-6 hrs between 2 coats)
  • Do normal painting process

B. For major damped areas

  • Mix Dampshield 2K Base: Catalyst: Cement in the ratio of 1:1:2 and apply as putty on the affected plaster area.
  • Give a curing time of 4-6 hours
  • Mix Dampshield 2K Base: Catalyst: Water in the ratio of 1:1:1
  • Apply one brush coat over it and dry it for again 4-6 hours.
  • Do normal painting process
Click for details

Leakage in Bathroom/ Kitchen/ RCC Tanks +

Leakage in Bathroom/ Kitchen/ RCC Tanks

Latex Shield 2K

Method of Application
Surface to be treated must be thoroughly cleaned from all kind of laitance, oils, grease etc.

  • Mix the powder into liquid gradually & stir well until to get homogeneous & uniform free flowing slurry.
  • Apply a slurry coat of mixed material through masonry brush.
  • Give drying time of six hours.
  • Apply the second coat similarly as first coat.
  • Leave the system to cure for at least 3 days.
  • Screed the surface if it is a foot traffic location. Go for normal painting if it is a internal/external wall.
Click for details
Leaking Roofs and Parapets

To stop damage of interiors due to water seepage from the rooftop use Latex Shield 2K & WC Kool & Seal. If the roof has leakage/Seepag use 2 coats of Latex Shield 2K followed by 2 coats of Kool & Seal to stop. This will stop the leakage & enhances the life of the roof.

Cracked Plasters +

Cracked Plasters

Crack Fill Powder/Crack Fill Paste

Method of Application

  • Fine hairline cracks must be widened up to 1 mm minimum followed by filling.
  • Surface to be treated must be thoroughly cleaned from all kind of laitance, oils, grease etc. Spray water if required to clean it thoroughly
  • Moisten the crack-surface before applying Crack Fill Paste/Powder
  • For powder mix water with powder in ratio of 2.5:1 (Powder : Water)
  • Press Crack Fill Paste/Powder into the cracks using a putty knife or spatula. Level the surface with a putty knife to get smooth & clean surface.
  • Further coat of Crack Fill Paste/Powder is undertaken after 24 hours of the application, when the first coat of Crack Fill Paste is completely cured.
  • Painter's putty or POP can be taken up once it is fully dry (at least 7 days).
Click for details

Weak Plasters/ Masonry Walls +

Weak Plasters/  Masonry Walls

Cementmix Plus

Method of Application

  • Charge cement & aggregates to the concrete mixer as per the mix design. Mix the dry ingredients for 2-3 minutes in dry condition.
  • Start addition of water into the mix upto 80% of the total quantity and mix for 3-4 minutes.
  • Cementmix Plus is to be added according to the recommended dosage into the remaining gauging water. Then add to the mixer and mix for another 2-3 minutes.
  • Discharge the concrete/plaster for application.
Click for details

Building Repairs +

Building Repairs

Advanced Latex Plus/Latex Plus

Method of Application
Surface to be treated must be thoroughly cleaned from all kind of laitance, oils, grease etc.

A. As Waterproofing Slurry/As Bond Coat:

  • Mix Advanced Latex Plus in the ratio of 1:4:7 (Advanced Latex Plus : Water : Cement) OR Latex Plus in the ratio 1:1.5 (Latex Plus : Cement)
  • Brush apply the 1st coat
  • While 1st coat is dry, apply 2nd coat (generally give 4-6 hrs between 2 coats)
  • Overlay the 2nd coat with screed/plaster for finish/protection.

B. As Repair Mortar:
For Waterproof Repair Plaster/ Structural Crack repair:

  • Mix Advanced Latex Plus in the ratio of 1:4:7 (Advanced Latex Plus : Water : Cement) OR Latex Plus in the ratio 1:1.5 (Latex Plus : Cement)
  • Apply 1 coat as bond coat with brush
  • Add 5KG Latex Plus/Advance Latex Plus in Cement : Sand : 1:3 with water 45% of cement.
  • Render the part with Cementmix Plus mixing with Cement (200ml in 50kg cement) & water as required.
Click for details
Stained Tiles

It is a long established fact that a reader will be distracted by the readable content of a page when looking at its layout. The point of using Lorem Ipsum.

Weak Tile Adhesion/ Leakage in Tile Joints +

Weak Tile Adhesion/  Leakage in Tile Joints

Tile Adhesive/Tile Adhesive Plus

Method of Application

  • Mix Tile Adhesive: Water = Approx. 3:1 (by vol.)
  • Spread the mixed adhesive to a thickness of approx. 3-6 mm on the back of the tile
  • Start placing tiles on the surface to be tiled.
  • Tap the tiles properly to ensure complete coverage of the backside of tiles & to eliminate the possibility of any air voids

Tile Grout

Method of Application

  • Tile Grout : Water = Approx. 3:1 (by vol.)
  • Apply Tile Joint Grout on the joints of the tiles.
  • Grout into the joints with a rubber sponge trowel or rubber grout squeeze.
  • The grouted joints must be left to dry & harden for around 2 hours before removing excess grout with a damp (not wet) sponge.
  • Allow the joints to be dried for 24 hours before polishing with a clean dry cloth.

Damp/ Wet Patches

X
Damp/ Wet Patches

Dampshield 2K

Method of Application
Surface to be treated must be thoroughly cleaned from all kind of laitance, oils, grease etc.

A. For minor damped areas

  • Mix Dampshield 2K Base: Catalyst: Water in the ratio of 1:1:1
  • Apply one brush coat over the affected area over the plaster
  • While 1st coat is dry, apply 2nd coat (generally give 4-6 hrs between 2 coats)
  • Do normal painting process

B. For major damped areas

  • Mix Dampshield 2K Base: Catalyst: Cement in the ratio of 1:1:2 and apply as putty on the affected plaster area.
  • Give a curing time of 4-6 hours
  • Mix Dampshield 2K Base: Catalyst: Water in the ratio of 1:1:1
  • Apply one brush coat over it and dry it for again 4-6 hours.
  • Do normal painting process
Click for details

Related Products

Dampshield 2k

Leakage in Bathroom/ Kitchen/ RCC Tanks

X
Leakage in Bathroom/ Kitchen/ RCC Tanks

Latex Shield 2K

Method of Application
Surface to be treated must be thoroughly cleaned from all kind of laitance, oils, grease etc.

  • Mix the powder into liquid gradually & stir well until to get homogeneous & uniform free flowing slurry.
  • Apply a slurry coat of mixed material through masonry brush.
  • Give drying time of six hours.
  • Apply the second coat similarly as first coat.
  • Leave the system to cure for at least 3 days.
  • Screed the surface if it is a foot traffic location. Go for normal painting if it is a internal/external wall.
Click for details

Related Products

Latex Shield 2k

Leaking Roofs and Parapets

X
Leaking Roofs and Parapets
  • It is a long established fact that a reader will be distracted by the readable content of a page when looking at its layout. The point of using Lorem Ipsum.

Related Products

Home Shield Home Shield

Cracked Plasters

X
Cracked Plasters

Crack Fill Powder/Crack Fill Paste

Method of Application

  • Fine hairline cracks must be widened up to 1 mm minimum followed by filling.
  • Surface to be treated must be thoroughly cleaned from all kind of laitance, oils, grease etc. Spray water if required to clean it thoroughly
  • Moisten the crack-surface before applying Crack Fill Paste/Powder
  • For powder mix water with powder in ratio of 2.5:1 (Powder : Water)
  • Press Crack Fill Paste/Powder into the cracks using a putty knife or spatula. Level the surface with a putty knife to get smooth & clean surface.
  • Further coat of Crack Fill Paste/Powder is undertaken after 24 hours of the application, when the first coat of Crack Fill Paste is completely cured.
  • Painter's putty or POP can be taken up once it is fully dry (at least 7 days).
Click for details

Related Products

Crack Fill Powder Crack Fill Paste

Related TVC

Weak Plasters/ Masonry Walls

X
Weak Plasters/  Masonry Walls

Cementmix Plus

Method of Application

  • Charge cement & aggregates to the concrete mixer as per the mix design. Mix the dry ingredients for 2-3 minutes in dry condition.
  • Start addition of water into the mix upto 80% of the total quantity and mix for 3-4 minutes.
  • Cementmix Plus is to be added according to the recommended dosage into the remaining gauging water. Then add to the mixer and mix for another 2-3 minutes.
  • Discharge the concrete/plaster for application.
Click for details

Related Products

Cementmix Plus

Related TVC

Building Repairs

X
Building Repairs

Advanced Latex Plus/Latex Plus

Method of Application
Surface to be treated must be thoroughly cleaned from all kind of laitance, oils, grease etc.

A. As Waterproofing Slurry/As Bond Coat:

  • Mix Advanced Latex Plus in the ratio of 1:4:7 (Advanced Latex Plus : Water : Cement) OR Latex Plus in the ratio 1:1.5 (Latex Plus : Cement)
  • Brush apply the 1st coat
  • While 1st coat is dry, apply 2nd coat (generally give 4-6 hrs between 2 coats)
  • Overlay the 2nd coat with screed/plaster for finish/protection.

B. As Repair Mortar:
For Waterproof Repair Plaster/ Structural Crack repair:

  • Mix Advanced Latex Plus in the ratio of 1:4:7 (Advanced Latex Plus : Water : Cement) OR Latex Plus in the ratio 1:1.5 (Latex Plus : Cement)
  • Apply 1 coat as bond coat with brush
  • Add 5KG Latex Plus/Advance Latex Plus in Cement : Sand : 1:3 with water 45% of cement.
  • Render the part with Cementmix Plus mixing with Cement (200ml in 50kg cement) & water as required.
Click for details

Related Products

Home Shield Home Shield

Related TVC

Stained Tiles

X
Stained Tiles
  • It is a long established fact that a reader will be distracted by the readable content of a page when looking at its layout. The point of using Lorem Ipsum.

Related Products

Home Shield Home Shield

Weak Tile Adhesion/ Leakage in Tile Joints

X
Weak Tile Adhesion/ Leakage in Tile Joints

Tile Adhesive/Tile Adhesive Plus

Method of Application

  • Mix Tile Adhesive: Water = Approx. 3:1 (by vol.)
  • Spread the mixed adhesive to a thickness of approx. 3-6 mm on the back of the tile
  • Start placing tiles on the surface to be tiled.
  • Tap the tiles properly to ensure complete coverage of the backside of tiles & to eliminate the possibility of any air voids

Tile Grout

Method of Application

  • Tile Grout : Water = Approx. 3:1 (by vol.)
  • Apply Tile Joint Grout on the joints of the tiles.
  • Grout into the joints with a rubber sponge trowel or rubber grout squeeze.
  • The grouted joints must be left to dry & harden for around 2 hours before removing excess grout with a damp (not wet) sponge.
  • Allow the joints to be dried for 24 hours before polishing with a clean dry cloth.

Related Products

Tile Adhesive Tile Grout

Related TVC

Click on the indicatorsto know more.

Latest Video

Latest News
Construction Chemicals
Toll Free No.
1800 103 6030
Close

Get in Touch

If you are planning to paint your home soon, share with us some details.

TOLL FREE NO: 1800-103-6030

SUBMIT